Changes for page Desktop Waterjet Cutting

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -1,11 +1,7 @@
1	1	|=(((
2		-(((
3		-WAZER Desktop Waterjet Cutting Machine
4		-)))
	2	+{{{WAZER Desktop Waterjet Cutting Machine}}}
5	5
6		-(((
7	7	[[Specs>>https://www.matterhackers.com/store/l/wazer-desktop-waterjet-cutter-machine/sk/MVN5VKM5]]
8		-)))
9	9	)))|=Working Area
10	10	(LxW)|=(% style="width: 376px;" %)Max Allowable Working Pressure|=(% style="width: 307px;" %)Max Working Flow Rate
11	11	|[[image:WazerPhoto.png||alt="omtechaf3555.jpeg" width="200"]]|(((
...	...	@@ -74,71 +74,113 @@
74	74
75	75	(Be aware of total physical space that the waterjet will occupy on a material, taking into account the width of the cut itself (kerf) )
76	76
77		-[[image:1772478615037-166.png||height="266" width="554"]]
	73	+[[image:1772478615037-166.png]]
78	78
79	79	== Materials Selection ==
80	80
81	81	Using the first dropdown menu, select the material category. Using the second dropdown menu, select the specific material you are cutting. If the specific material is not listed, consult an RPS studio staff member. Once category and material type are selected, input the material thickness in either millimeters or inches.
82	82
83		-[[image:1772478775055-319.png||height="264" width="550"]]
	79	+[[image:1772478775055-319.png]]
84	84
85		-== Cutting Path Adjustments ==
	81	+== Cutting Path Adjustments ==
86	86
87	87	Change the cutting path to match the design of your file.
88	88
89		-Outside: Will cut outside the lines of your part by a user given offset.
	85	+Outside: Will cut outside the
90	90
91		-Centerline: Will cut directly on the lines of your part.
	87	+= Machine Setup (not done :0 ) =
92	92
93		-Inside: Will cut inside the lines of your
	89	+The Long focal length lens in our large-format OMTech laser cutter allows for more efficient cuts in thicker materials. However, this comes at the cost of a slightly large spot size, and thus, less fine engraving abilities.
94	94
95		-= Machine Setup =
	91	+Use the table below to input the correct values for your material. Note that for engraving, the thickness does not matter, because it won't cut all the way through. We also have sample engravings at various settings in the RPS if you would like to change the depth or darkness of the engraving. Keep in mind that the depth and color might not be exact, as they depend highly on laser focus and various other environmental parameters that cannot be controlled.
96	96
97		-== Turning Machine On ==
	93	+**Cutting Table**
98	98
99		-1. Place SD card with part file into the right side of the wazer jet machine. **(SD cards are not provided)**
100		-1. Twist the E-Stop button to where it releases, the screen should begin to turn on.
101		-1. Check that the button on the bottom right of the machine is set to "On" (if screen is still not turning on, consult a staff member)
	95	+|=**Material**|=Speed|=Max Power|=Min Power|=Passes
	96	+|1/8" (3 mm) Birch Plywood|45 mm/s|70%|35%|1
	97	+|1/4" (6 mm) Birch Plywood|15 mm/s|70%|35%|1
	98	+|1/16" (1.5 mm) Cast Acrylic|90 mm/s|70%|20%|2
	99	+|1/8" (3 mm) Cast Acrylic|55 mm/s|70%|20%|2
	100	+|1/4" (6 mm) Cast Acrylic|20 mm/s|70%|70%|2
	101	+|1/16" (1.5 mm) Buna N Rubber|80 mm/s|70%|20%|1
102	102
103		-== Setting Up ==
	103	+**Engraving Table**
104	104
105		-1. On the starting screen there will be two options, "Select Cut File" and "Setup & Maintenance". Press the OK button to Select the Select Cut File option.
106		-1. Scroll down until the cursor is next to the file you created earlier, and hit OK
107		-1. Loosen the Nozzle securing knob, pull the nozzle up, and retighten the nozzle securing knob, press OK to home the nozzle
108		-1. Fill the grit hopper on the left side of the machine, hit OK
109		-1. Check to make sure the blue water valve is in line with the vertical pipe, hit OK
110		-1. Secure the material to the cut bed using the screws and a screwdriver, hit OK
111		-1. Now that the arrow keys can be used to move the nozzle over the material, remove the plastic cover off of the cutting head.
112		-1. Loosen the nozzle securing knob, and place the tab side of the plastic cover underneath the nozzle.
113		-1. Lower the nozzle until it makes contact with the plastic tab, and tighten the nozzle securing knob and place the plastic cover back on top of the cutting head. Hit OK.
114		-1. The next screen will have several options. Before doing anything else, **move the origin to the location of your choosing**
115		-1*. Move Origin - allows you to move the origin for the program to a location of your choosing. **DO THIS FIRST.**
116		-1*. Cut - sends you to the next screen where you must press the Start button to begin cutting.
117		-1*. Dry Run - Follows the exact cutting path of the program without firing the waterjet.
118		-1*. Check Extents - Outlines the bounding box of the area being cut
119		-1*. Restart cut - if the cut fails or stops in the middle, this will restart the program in the Dry Run state and will allow you to resume the cut at any point along the program.
120		-1*. Cancel - sends you back to the starting screen.
	105	+|=**Material**|=Speed|=Max Power|=Min Power|=Passes
	106	+|Birch Plywood|475 mm/s|50%|35%|1
	107	+|Cast Acrylic|550 mm/s|20%|20%|1
121	121
122		-== Run Part ==
	109	+Settings can be changed within Lightburn or on the physical OMTech Laser in the highlighted portion on the display screen. Please consult with a technician before changing speeds and power on the machine.
123	123
124		-***You must remain with the machine for the entirety of the cut* **
125	125
126		-* It may be necessary to refill the water in the machine before running. Use the white 3 gallon bucket to pour more water into the tank directly. The water level should sit right below the surface of the bed.
127		-* Monitor the level of the grit while the part is running, if it's running low, machine will automatically stop the cut and shut off.
128		-* It is recommended to keep the hoppers topped off
129		-* If water starts pouring out from under the hoppers, the machine is having a backflow problem, **SHUT IT OFF with the E-Stop and notify RPS Staff.**
	112	+[[image:omtech12.jpg||alt="https://wiki.rapidprototypingstudio.com/learning/omtech12.jpg" height="40%" width="40%"]]
130	130
131		-== Clean Up ==
	114	+== Dremel Laser Settings ==
132	132
133		-1. Remove your part and any excess material from the bed.
134		-1. Clean material and part(s) off by dunking them in the grit catchers/water bucket. **DO NOT wash grit down the sink.**
135		-1. Pull the grit catchers out and drain the excess water back into the tank.
136		-1. Once the majority of the water is drained, dump the grit into the orange 5 gallon bucket
137		-1. Place the grit catchers back into the machine.
	116	+All settings are preset within the Dremel's IP address site.
138	138
139		-== ==
	118	+== Unsafe Materials for Laser Cutting ==
140	140
141		-== Required PPE ==
	120	+* ABS
	121	+* Beryllium oxide
	122	+* Carbon
	123	+* Chlorinated plastics
	124	+* Coated carbon fiber
	125	+* Coated materials
	126	+* Epoxy-based or phenolic resins
	127	+* Fiberglass
	128	+* Fluorine-based plastics:
	129	+** PTFE (Teflon)
	130	+** Fluorinated ethylene propylene (FEP)
	131	+* Galvanized metal
	132	+* HDPE (High-Density Poly Ethylene)
	133	+* Leather, Artificial or Chrome tanned
	134	+* Materials containing:
	135	+** Astatine
	136	+** Bromine
	137	+** Chlorine
	138	+** Fluorine
	139	+** Formaldehyde
	140	+* Wood containing:
	141	+** Flame-retardants
	142	+** Halogens
	143	+** Iodine
	144	+* Wood that has been:
	145	+** Coated
	146	+** Fumigated
	147	+** Pressure-treated
	148	+** Stained
	149	+* Mirrored surfaces
	150	+* Nylon
	151	+* Painted material
	152	+* Varnished materials
	153	+* Particleboard, paneling
	154	+* Polycarbonate
	155	+* Polychloroprene (CR or chloroprene rubber, marketed under the brand name Neoprene)
	156	+* Polypropylene foam
	157	+* Polypropylene sheet
	158	+* Polystyrene foam
	159	+* Polyurethane
	160	+* Polyurethane foam
	161	+* Polyvinyl chloride (PVC)
	162	+* POM Delrin/acetyl
	163	+* Rubber
	164	+* Styrofoam
142	142
143		-* Close toed shoes
144		-* Eye glasses/goggles
	166	+== Post Processing ==
	167	+
	168	+**Required PPE** for woods and acrylic:
	169	+
	170	+* None
	171	+
	172	+Once the job has concluded, allow the fumes to be vented for a minimum of 10 seconds. Please note that woods will have charring which is not harmful but may transfer to your hands or anything else it touches. If desired, you may sand the wood with the sandpaper we have in stock or use a sander. For acrylic sheets, peel off the protective film once ready for personal/project use.
	173	+
	174	+**Required PPE** for rubber:
	175	+
	176	+* Latex or Nitrile gloves
	177	+
	178	+[[image:ppe_gloves.png||height="100"]]
	179	+
	180	+Once the job has concluded, allow the fumes to be vented for a minimum of 30 seconds. Please note that rubber materials will char as well and it is best practice to wear gloves while handling them. Rinse the rubber cuts under water to wash off as much charred edges as possible.
	181	+
	182	+If you need assistance, RPS staff are always present to help with advice! **Please ensure that you return hand tools to their proper locations, and turn off the machine once use is complete.**